9/13/2021
33
  1. Asme Sfa 5.14
  2. Asme Sec Iic Sfa 5.14
  3. Asme Sfa 5.14 Ernicrmo-3

View Product Datasheet
View Product SDS

INTERNATIONAL CLASSIFICATIONS

Asme sec iic sfa 5.14

ANSI/AWS A5.14 ERNiCr-3

5.14

ASME SFA 5.14 ERNiCr-3

FEATURES & APPLICATIONS

This standard covers chromium and chromium-nickel stainless welding rods and bare electrodes for nuclear and associated applications. Material shall conform to the requirements of ASME SFA-5.9; to the requirements of the ASME Boiler and Pressure Vessel Code (ASME Code), Section III, Article NB-2000; and to the additional requirements of this standard. NOMINAL COMPOSITION Ni+Co 55 max Cr 17 – 21 Cb+Ta 4.75 – 5.5 Mo 2.8 -3.3 Ti.65 – 1.15 Al.2 –.8 Co 1 max C.08 max Mn.35 max Si.35 max P.015 max S.015 max B.006 max Cu.3 max Fe Balance STANDARD SPECIFICATIONS AMS 5596 AMS 5662 AMS 5663 AMS 5664 AMS 5832 ASME Case 2222-1 ASME SFA 5.14 ASTM B 637 ASTM B 670 EN 2.4668 GE B50TF14 GE. ASME SB-435 Plate, Sheet & Strip; ASTM B 572 Rod; ASME SB-572 Rod; ASTM B 619 WELD Pipe; ASME SB-619 WELD Pipe; ASTM B 622 SMLS Pipe; ASME SB-622 SMLS Pipe; ASTM B 626 Tubing; ASME SB-626 Tubing; ASME SFA-5.14 ERNiCRrMo-2 Weld Wire. SFA-5.14/SFA-5.14M SPECIFICATION FOR NICKEL AND NICKEL-ALLOY BARE WELDING ELECTRODES AND RODS SFA-5.14/SFA-5.14M (Identical with AWS Specification A5.14/A5.14M:2011.

6082 is a nickel -chromium-iron filler metal used for TiG welding of nickel base Inconel® 600, 601 and 690 as well as Incoloy® 330, 800 and 800 HT to themselves or to carbon steel, stainless steel, high nickel base 200 and to nickel-copper Monel® 400. 6082 can also be used for joining high nickel base 200 to stainless steel, nickel-copper Monel® 400 to carbon steel and for overlaying on steel. Used for welding of ASTM B163, B166, B167 and also B168 having UNS N06600.

Asme Sfa 5.14

AWS Chemistry Requirements

C

Mn

Fe

P

S

Si

Cu

Ni+Co

.10 Max

2.5 – 3.5

3.0 Max

.03 Max

.015 Max

.50 Max

.50 Max

67 Min.

Nb(Cb)+Ta

Co

Cr

Ti

2.0 – 3.0

.12 Max If Specified

18.0-22.0

.75 Max

Typical Mechanical Properties

Undiluted Weld MetalMaximum Value Up to:

Tensile Strength 80,000 psi

Yield Strength 40,000 psi

Asme Sfa 5.14

Elongation 30%

Welding Procedures

Asme Sec Iic Sfa 5.14

Typical GTAW (TiG) Welding Procedures: DCEN with EWTh-2 truncated conical tip

Filler Wire Size

Tungsten

Amps

Volts

Gas Cup Size

Argon (cfh)

Base Thickness

1/16″

1/16″

80-150

12

1/2″

20

1/16″-1/8″

3/32″

3/32″

150-250

12

3/4″

25

1/8″-3/16″

1/8″

1/8″

Hyster 80 forklift specs. 200-375

12

5/8″

30

1/4″-1/2″

Procedures may vary with change in position, base metals, filler metals, equipment and other changes.

AVAILABLE SIZES: TN 82/ = Cut lengths of 030, 035, 045, 1/16, 3/32, 1/8, 5/32

Asme Sfa 5.14

Asme Sfa 5.14 Ernicrmo-3

Other sizes available – please inquire

6817.info – 2018